1962 Chevy Truck - Classic Custom Truck

In the world of custom trucks, it takes a lot these days to turn heads. Perfect paint, custom engine work, an immaculate interior, and you name it. Meanwhile, all of the competition has cool stuff, too. Many folks have raised their game to this level, and what used to be a show winner can now easily get lost in a crowd.

The main components of the system are two Autoloc 250-pound LA8 actuators and two motor-control modules. Tom Elliott, owner of BAD Rods & Restorations, also set up the system to be activated with a key-fob remote.

The main components of the system are two Autoloc 250-pound LA8 actuators and two motor-co

One interesting modification sure to turn heads is an automatic hood-lift system. We have seen something similar with tonneau covers, but automatically lifting the hood on a custom truck is much more rare because it involves a little more engineering. Tom Elliott, the owner of BAD Rods & Restorations, has put together a system for a customer's '62 Chevy that is ingenious in its simplicity. The good news here is that Elliott's system doesn't use any one-off billet components that are impossible for the average Joe to obtain. Instead, along with two Autoloc 250-pound actuators and control modules, most of the system can be fabricated with little more than a welder, a grinder, and some hours in the garage.

Elliott was able to keep the existing hood hinges, which minimizes the number of pieces that must be fabricated and helps to keep the massive hood stable as it is raised and lowered. In order to keep the geometry correct, the actuators must be mounted inside of the cab to push on the hinges, but they are in a location where it can easily be fabricated from 18-gauge steel plate and some square tubing. A Lexan board mounted on the back of the cab, and behind the seat, serves as the perfect mount for the remote-control receivers, the control module, and the rest of the electronics.

Operating the system is also quite simple. A hood release latch is mounted underneath the steering column in the cab of the truck. Once the latch is released, the hood is raised with Autoloc's motor control unit with a touch of a button on the remote key fob. The control unit can be programmed to extend and retract to whatever point the operator desires. So once the actuators are started, they will raise the hood to the fully open position and then stop. Likewise, it can also be programmed to lower the hood slowly until the latch catches and stops.

Tom kept the hood hinges, but he tossed the springs and spring mounts (shown in its original position). This significantly cleaned up the look underneath the hood.
Tom kept the hood hinges, but he tossed the springs and spring mounts (shown in its origin
The best position to mount the actuator is mapped out on the side of the cab. To give the actuators the best leverage on the push points of the hood hinges, they must be mounted horizontally. The tape mark is a straight line from the planned mounting point to the hinge.
The best position to mount the actuator is mapped out on the side of the cab. To give the
Once the correct locations for the attachment points of the actuators are located, a hole can be cut in the firewall. Since the pushrod end of the actuator will move up as it pushes on the hood hinge, the hole in the firewall must be oval, to allow for the movement.
Once the correct locations for the attachment points of the actuators are located, a hole

David Williams used cardboard to mock up a mounting bracket. Because the height of the push point of the hinge moves as the hood is raised, the motor side of the actuator must be able to pivot around the mounting point. David also decided to use the bracket as a cover for the access hole to the side panel.
David Williams used cardboard to mock up a mounting bracket. Because the height of the pus
After finding the best feasible design, the cardboard mock-up was remade in 18-gauge plate steel, a section of square tubing, and fastening hardware. The actuator must be able to swivel; it cannot be bolted solid to the plate. The square tubing provided a solid mounting point that also allows the base of the actuator to swivel freely.
After finding the best feasible design, the cardboard mock-up was remade in 18-gauge plate
Because the mounting bracket must be removable, in order to access the wiring for the power windows and other accessories that go to the door, it was held in place with sheetmetal screws. Elliott said he's also considering welding in threaded inserts for a more secure mount, but so far the screws are holding up very well.
Because the mounting bracket must be removable, in order to access the wiring for the powe