• Diy Subwoofer Enclosure Console Removed
    The '07 Chevrolet Avalanche factory center console was removed to make room for a more-vocal subwoofer center-console enclosure.
    Diy Subwoofer Enclosure Console Removed
    The '07 Chevrolet Avalanche factory center console was removed to make room for a more-voc
  • Diy Subwoofer Enclosure Trace Template
    Danny Hentges used cardboard to make a profile pattern of the center console enclosure.
  • Diy Subwoofer Enclosure Cardboard Template
    Here is the cardboard profile pattern that was transferred onto a sheet of medium-density fiberboard (MDF).
    Diy Subwoofer Enclosure Cardboard Template
    Here is the cardboard profile pattern that was transferred onto a sheet of medium-density
  • Diy Subwoofer Enclosure Template Test
    After drawing and cutting out the pattern, Danny tried the armrest for comfort.
  • Diy Subwoofer Enclosure Rough Cut
    After transferring the profile pattern onto the sheet of 3/4-inch thick MDF, it was then rough-cut on a table saw.
    Diy Subwoofer Enclosure Rough Cut
    After transferring the profile pattern onto the sheet of 3/4-inch thick MDF, it was then r
  • Diy Subwoofer Enclosure Cut Panels
  • Diy Subwoofer Enclosure Fasten Center Pieces
    After the larger inner side pieces were rough-cut, they were aligned, then fastened together by using 1-inch long brads.
    Diy Subwoofer Enclosure Fasten Center Pieces
    After the larger inner side pieces were rough-cut, they were aligned, then fastened togeth
  • Diy Subwoofer Enclosure Router
    By using a router table, a vertical bit was chucked up, then the nailed pieces were drawn around the router bit. This procedure made both pieces identical.
    Diy Subwoofer Enclosure Router
    By using a router table, a vertical bit was chucked up, then the nailed pieces were drawn
  • Diy Subwoofer Enclosure Round Edges
    A round-nose bit was chucked up in the router. The edges were carefully trimmed with a decorative radiused edge.
    Diy Subwoofer Enclosure Round Edges
    A round-nose bit was chucked up in the router. The edges were carefully trimmed with a dec
  • Diy Subwoofer Enclosure Separate Pieces
    After the nailed pieces outside the perimeter edges were shaved equally with the router, the two pieces were then separated.
    Diy Subwoofer Enclosure Separate Pieces
    After the nailed pieces outside the perimeter edges were shaved equally with the router, t
  • Diy Subwoofer Enclosure Accent Piece
    A smaller inside diameter piece was cut and routed, which gave the sides of the console some dimension, definition, and style.
    Diy Subwoofer Enclosure Accent Piece
    A smaller inside diameter piece was cut and routed, which gave the sides of the console so
  • Diy Subwoofer Enclosure Cut Inside Piece
    A jigsaw was used to cut and remove a section from the smaller inside piece.
  • Diy Subwoofer Enclosure Smooth Inside Edge
    With the inner pieces removed from both smaller inside pieces, they were nailed together and traced with the router, breaking the edges.
    Diy Subwoofer Enclosure Smooth Inside Edge
    With the inner pieces removed from both smaller inside pieces, they were nailed together a
  • Diy Subwoofer Enclosure Enclosure Hole
    Again using the jigsaw, Danny cut a 9-5/8-inch-diameter hole in the enclosure's floor to mount the 10-inch-diameter subwoofer.
    Diy Subwoofer Enclosure Enclosure Hole
    Again using the jigsaw, Danny cut a 9-5/8-inch-diameter hole in the enclosure's floor to m
  • Diy Subwoofer Enclosure Panel Cut
Enjoyed this Post? Subscribe to our RSS Feed, or use your favorite social media to recommend us to friends and colleagues!
stumble upon rss